Make a Small DIY Sandblasting Cabinet

Perfect for the Air Eraser

If you have a mini sandblasting tool to etch glass, also known as an air eraser, you know the importance of protecting yourself from the aluminum oxide compound. Even though the use of the air eraser is done outside, I still don’t want to breathe in the compound or have to change my clothes every time I use it. This small DIY sandblasting cabinet is all over the internet (so I can’t take credit for the design) but I can tell you how to make your own! I searched everywhere for instructions and did not find them, so I created a tutorial…

Small DIY Sandblasting Cabinet

Materials:

  • 66 quart plastic tub with lid
  • 1 sheet of 18″ x 24″ Non-Glare Plexiglas (<– affiliate link!)
  • 2 toilet flanges
  • 1 rubber grommet – the center diameter should be a little larger than the diameter of the hose on the air eraser
  • 12 – 1/2″ machine screws with nuts and washers
  • 16 – 3/4″ machine screws with nuts and washers
  • 1 set of rubber gloves (like the type for dishwashing)
  • Clear silicone

Small DIY Sandblasting Cabinet top view

Start by cutting out the center of the lid. Leave enough of a margin to install the shorter machine screws. My plastic tub had a nifty curved design in the top so when I cut the top out, I followed this line. I used a Dremel Trio (which promptly died when I was finished – ugh!) with a straight bit to cut out the center – a jigsaw or a handsaw can also be used. The plastic is really easy to cut through!

Small DIY Sandblasting Cabinet cutting the top

Measure the opening and cut the Plexiglas larger than the opening by at least 3/4″ on each side. Use a straightedge and a knife to score the Plexiglas, then snap it along the line.

Small DIY Sandblasting Cabinet tools to cut Plexiglas

Make marks along the border of the Plexiglas to drill holes for the screws.

Small DIY Sandblasting Cabinet hole drilled in Plexiglas

Clamp the Plexiglas to the lid (with the Plexiglas on the underside of the lid), then mark the position of the holes and drill through the lid. I inserted a screw into each hole as I drilled it to keep the Plexiglas lined up with the lid. Clear silicone would be a great idea to help secure the Plexiglass to the lid as well.

Small DIY Sandblasting Cabinet marking the top

Secure the Plexiglas to the lid using the 1/2″ machine screws, each with a washer and a nut.

Small DIY Sandblasting Cabinet completed lid

Small DIY Sandblasting Cabinet close up of lid

Mark the position to cut the hole for the flanges. I’ve seen some of the tubs with both holes on one longer side, and some like I did it – one hole on a shorter side, and one hole on a longer side (I think this adds a greater degree of movement inside the tub). Measure the center of the flanges – this will be the size to cut the holes. Clamp a scrap piece of lumber on the inside of the tub and cut out the holes with a hole saw. The scrap board will help make a cleaner hole during drilling. A jigsaw can also be used to cut the holes. Make the circle for the cut by tracing the outside of the pipe part of the flange.

Small DIY Sandblasting Cabinet marking for toilet flange

Small DIY Sandblasting Cabinet hole for toilet flange

Apply the clear silicone to the flanges, then fit the cuffs of the gloves over the flanges.

Small DIY Sandblasting Cabinet silicone on toilet flange

Small DIY Sandblasting Cabinet dishwashing glove on toilet flange

Insert the flanges in the holes drilled into the tub. Make sure the thumbs of the gloves face up, as if you are shaking hands. Mark the position of the smaller holes, then drill them out. Secure the flanges in place with the 3/4″ machine screws, washers, and nuts.

Small DIY Sandblasting Cabinet toilet flange install

On the opposite side of the tub, drill a hole toward the top for the air eraser hose. The hole will be a little larger than the hose. Install the rubber grommet in the hole.

Small DIY Sandblasting Cabinet rubber grommet

Thread the line for the air eraser through the hole with the rubber grommet, and connect the air eraser.

Small DIY Sandblasting Cabinet air eraser line hose

Small DIY Sandblasting Cabinet completed view

The blasting cabinet is now ready for use! I love using it but the only problem I have with mine is that the gloves fit a little too snug and I have a hard time getting my hands out. It will have to suffice until these gloves wear out! Also, non-glare Plexiglas would’ve been really nice, ha ha!  Have any questions about the small DIY sandblasting cabinet? Leave a comment below!

Originally posted 2014-05-29 08:00:34.

14 Comments

Leave a Reply to VStrong Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.