How to Make a Wall Mounted Lighting Piece

Power Tool Challenge – A Project Using a Drill

I was invited to join a few fellow bloggers for a Power Tool Challenge. The challenge is to make a project using one power tool and in this case, a drill. The challenge is designed to show new woodworkers and DIYers that a ton of fancy tools are not needed to create a fabulous project. I’m going to show how to make a wall mounted lighting piece.

How to Make a Wall Mounted Lighting Piece

For this project, I used an old lighting fixture I found at my local Habitat for Humanity ReStore which I took apart and spray painted a new color. I also rewired it to use new sockets and a plug. The wall mount light fixture hangs on the wall using a metal cleat and plugs into an outlet below.

Supplies:

  • 1 – 1×6 board at 8′ cut in four equal lengths
  • 1 – 1×3 board at 4′ cut at approximately 22″ long
  • Pocket hole jig with 1-1/4″ pocket hole screws
  • Wood glue
  • Sandpaper in 80 grit, 120 grit, and 220 grit
  • 1″ Forstner Bit
  • 3/8″ drill bit
  • Wood stain and sealer
  • Old light fixture
  • Replacement lamp cord with a plug
  • Wire nuts & electrical tape
  • Metal picture hanging cleat

I started by taking the entire fixture apart and wiping it down with a bit of vinegar. I then used a red oxide primer to prime every piece. I spray painted the entire fixture using spray paint in Cobalt Blue. I set everything off to the side to thoroughly dry.

The 1×6 board will be cut into four equal pieces which will measure approximately 23-7/8″ long. The 1×3 board will be cut into two pieces approximately 22″ long. If the boards are purchased at Home Depot, they will cut the boards for free. For future reference, they will not cut anything shorter than 12″ for safety reasons.

Set the pocket hole jig for 3/4″ material. Drill pocket holes along one long edge of each 1×6 piece except one. Also drill two pocket holes in the shorter ends of each board. Do not drill any pocket holes in the 1×3 boards. Secure the boards together using glue and 1-1/4″ pocket hole screws. Attach the 1×3 pieces to the sides of the 1×6 boards using glue and 1-1/4″ pocket hole screws.

How to Make a Wall Mounted Lighting Piece_Base

Thoroughly sand the boards starting with 80 grit, moving to 120 grit, and finishing with 220 grit. Before I stained the boards, I marked the position for the mounting holes of my light fixture on the back side. I drilled the holes about 1/4″ deep using the 1″ Forstner bit. I used the 3/8″ bit to drill a hole in the center of the holes made by the Forstner bit. The holes are now countersunk to accommodate the nuts when mounting the light fixture. I also drilled a 3/8″ hole in between the countersunk holes to allow for the lamp cord.

How to Make a Wall Mounted Lighting Piece_Marking Holes

How to Make a Wall Mounted Lighting Piece_Forstner Bit

How to Make a Wall Mounted Lighting Piece_Countersunk Hole

I stained the piece with a dark brown stain first and let it dry, then continued with a weathered grey stain. I sealed the boards with three coats of polyurethane.

Once the boards were dry, I mounted the light fixture using 2-1/2″ long lamp pipe with light fixture braces. The pipe went through the countersunk holes I drilled with the Forstner bit and were secured with a nut on the back. The light fixture you use will probably mount to the boards in a different way. Please feel free to contact me and I will walk you through the steps to mount the fixture to the boards!

How to Make a Wall Mounted Lighting Piece_Mounting Brace

How to Make a Wall Mounted Lighting Piece_Nut

I wired this light fixture to use a plug and wrote a post on how to rewire a light fixture to use a plug.

How to Make a Wall Mounted Lighting Piece_Wiring

The fixture was positioned over the lamp pipe pieces and secured with rosettes and caps that are original to the fixture.

How to Make a Wall Mounted Lighting Piece_Mounting Pipe

How to Make a Wall Mounted Lighting Piece_Mounting Rosettes

I installed the metal cleat on the back of the boards according to the manufacturer’s instructions. These cleats are great because they are small and hold a lot of weight!

How to Make a Wall Mounted Lighting Piece_Cleat

I purchased new globes (which were expensive but worth it!) then attached them to the fixture, and I installed new LED bulbs.

How to Make a Wall Mounted Lighting Piece_Finished

How to Make a Wall Mounted Lighting Piece_Single

How to Make a Wall Mounted Lighting Piece_Lighted

Here are projects from the other participants in the Power Tool Challenge:


Any questions on how to make a wall mounted lighting piece? Leave a comment below or contact me at cher {at} designsbystudioc {dot} com! I am always glad to help!

Originally posted 2015-05-14 07:00:18.

10 Comments

  • Wendi Wachtel says:

    Cher, I’m so glad you shared this project! I would not have guessed redoing a wall mount light and mounting it onto a board would be easy. That was such an awesome tutorial. I love those cleats by the way, I’ve seen them in action and am planning to use them to hang a mirror soon:) Thanks so much for joining in on the One Power Tool Challenge!

  • Apieceofrainbow Ananda says:

    this is beautiful Cher!! i am totally looking for an old fixture thanks to you! =) love the transformation!! xo

    • CherTexter says:

      Thank you so much, Ananda! I have had the fixture for a couple of years but wasn’t sure what I wanted to do with it… I love how this project came out!

  • Krista says:

    What a cool idea! I have never seen that before!! Fun to be on this challenge with you Cher – have a great weekend!

    • CherTexter says:

      Thank you so much, Krista! It has been fun meeting new like-minded people! Thank you for stopping by!

  • Amyhb says:

    This is a super cool project, crazy you only needed a drill. The light fixture is fun, love the blue.

    • CherTexter says:

      Thank you, Amy! I love the blue, as well, and it was such an easy project! Thanks for stopping by!

  • […] I got together with fellow bloggers to create a project using one power tool – a drill. I made a wall mounted light fixture that was really easy and looks fabulous! After taking the summer off, we are back with a new […]

  • […] a professional to ensure a proper and safe installation. However, if you’re confident in your DIY skills, here are some tips to guide […]

Leave a Reply to Wendi Wachtel Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.