The Cabot Wine Rack Plans

Free DIY Wine Rack Plans You Can Build Today

There is something really awesome about a wine collection… There is something even more awesome about a cabinet or rack in which to display the collection! Featuring three drawers, and a cubby with a shelf and glass door, the Cabot Wine Rack Plans will display your collection in style with extra storage for glasses or other “spirits”!

cabot wine rack plans_Copy

Materials:

  • 1-1/4″ pocket hole screws
  • 1-1/4” brad nails
  • Edge banding, optional
  • 1 set of hinges
  • 4 cabinet pulls
  • Turnbuttons or glass clips to hold glass in place on the door
  • Wood glue
  • Sandpaper (100, 150, 220 grits)
  • Finishing supplies (primer & paint, or stain, sealer)
  • Paste Wax

Lumber:

  • 1 – 1×2 at 4′
  • 2 – 1×3 at 6′
  • 2 – 2×2 at 8′
  • 1 sheet of 3/4″ plywood
  • 1 half sheet of 3/4″ plywood

Cut List:

  • 4 – 2×2 at 44-1/2″ – Legs
  • 2 – 3/4″ plywood at 13-1/2″ x 40-1/2″ – Side Panels
  • 1 – 3/4″ plywood at 16″ x 40-1/2″ – Back Panel
  • 4 – 3/4″ plywood at 15-3/4″ x 16″ – Lower Shelves
  • 1 – 3/4″ plywood at 14-1/2″ x 16″ – Upper Shelf
  • 4 – 1×3 at 16″ – Wine Cradle
  • 1 – 1×2 at 16″ – Stretcher
  • 1 – 3/4″ plywood at 17″ x 20″ – Top
  • 3 – 3/4″ plywood at 14-1/4″ x 14-1/4″ – Drawer Bottoms
  • 6 – 3/4″ plywood at 2-7/8″ x 14-1/4″ – Drawer Sides
  • 6 – 3/4″ plywood at 2-7/8″ x 15-3/4″ – Drawer Front & Back
  • 2 – 3/4″ plywood at 2″ x 26-3/4″ – Door Stiles
  • 3 – 3/4″ plywood at 2″ x 11-3/4″ – Door Rails

cabot wine rack plans

Notes About the Project:

If using edge banding, it will be applied to the exposed edges of the plywood before assembly.

Step One

Cut the pieces for the legs and the side panels. With the pocket hole jig set for 3/4″ material, drill pocket holes in each longer edge of the panels. Secure to the legs using glue and 1-1/4″ pocket hole screws. The back face of the panels will be flush with the inside face of the legs.

 cabot wine rack plans_Sides

Step Two

Cut the piece for the back panel and drill pocket holes along each longer edge. Secure to the legs using glue and 1-1/4″ pocket hole screws. The back face of the panel will be flush with the outside face of the legs.

 cabot wine rack plans_Back

Step Three

Cut the pieces for the lower shelves and drill pocket holes in the side and back edges. Secure in the cabinet using glue and 1-1/4″ pocket hole screws. The bottom of the lowest shelf will be flush with the bottom edges of the back and side panels. It may be easier to start with the highest shelf and work down!

 cabot wine rack plans_Lower Shelves

Step Four

Cut the piece for the stretcher and drill pocket holes in each end. Secure to the front legs using glue and 1-1/4″ pocket hole screws.

 cabot wine rack plans_Stretcher

Step Five

Cut the piece for the upper shelf and drill pocket holes in the side and back edges. Position the shelf so it is 1-1/4″ back from the front face of the front legs, then secure using glue and 1-1/4″ pocket hole screws.

 cabot wine rack plans_Upper Shelf

Step Six

Cut the pieces for the cradle. It is easier to cut one piece and mark the position for the holes, cut the holes using a hole saw, then rip the board in half on the table saw. A jigsaw to cut the curves can also be used – just do what works! Mark the position for the cradles then secure as shown using glue and 1-1/4″ brad nails from the outside of the side panels.

 cabot wine rack plans_Cradle 1

cabot wine rack plans_Cradle 2

Step Seven

Cut the piece for the top. Position the top so that the front and sides overhang by 1/2″. Secure using glue and 1-1/4″ brad nails.

 cabot wine rack plans_Top

Step Eight

Cut the pieces for the drawer boxes. Drill pocket holes in all four edges of the bottom as well as each end of the sides. Assemble the drawer box as shown using glue and 1-1/4” pocket hole screws.

 cabot wine rack plans_DrawersBS

cabot wine rack plans_DrawersFB

 

cabot wine rack plans_Drawers

Step Nine

Cut the pieces for the door frame. Drill pocket holes in each end of the shorter pieces, then assemble the door using glue and 1-1/4″ pocket hole screws. Install the hinges on the door, then install the door in the cabinet.

 cabot wine rack plans_Door 1

cabot wine rack plans_Door 2

Finish as desired! Apply a coat of past wax to the bottom of each drawer to help it slide smoothly on each shelf. Position the glass on the inside of the door, then secure with glass clips or turnbuttons. Install the cabinet pulls on the door and drawers.

These Cabot wine rack plans will have you showing off your DIY skills and producing a fab piece of furniture in no time! Need help with the plan? Let me know at cher {at} designsbystudioc {dot} com!

4 Comments

Leave a Reply to CherTexter Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.