DIY Plans to Build a Cate Chest
A Small Cabinet with Lots of Storage
This little cabinet can serve a great purpose in so many rooms… The free furniture plans to build a Cate Chest feature a drawer on top and a door at the bottom with two shelves inside. The drawer front and door are pieced to make it look vintage! This is a very easy build and this is one of those projects that can be finished in a weekend!
- 1-1/4″ pocket hole screws (<– affiliate link!)
- 1-1/4″ brad nails
- 1-3/4″ brad nails
- Edge banding (<– affiliate link!)
- 1 set of hinges
- Wood glue (<– affiliate link!)
- Sandpaper (100, 150, 220 grits) (<– affiliate link!)
- Finishing supplies (primer & paint, or stain, sealer)
- 1 – 1×2 at 4′
- 1 – 1×3 at 6′
- 2 – 2×2 at 6′
- 1 – 2′ x 4′ sheet of 1/4″ plywood
- 1 – 4′ x 8′ sheet of 3/4″ plywood
- 4 – 2×2 at 29-1/4″ – Legs
- 2 – 1×2 at 12″ – Side Framing
- 2 – 3/4″ plywood at 12″ x 23-3/4″ – Side Panels
- 2 – 3/4″ plywood at 14″ x 15″ – Upper Shelf & Bottom
- 1 – 3/4″ plywood at 13-1/2″ x 14″ – Center Shelf
- 1 – 1/4″ plywood at 15-1/2″ x 24-7/8″ – Back
- 1 – 3/4″ plywood at 15-1/2″ x 18″ – Top
- 2 – 3/4″ plywood at 5-1/2″ x 12-3/4″ – Drawer Box Sides
- 1 – 3/4″ plywood at 12-3/8″ x 12-3/4″ – Drawer Box Bottom
- 2 – 3/4″ plywood at 5-1/2″ x 13-7/8″ – Drawer Box Front & Back
- 1 – 1×3 at 13-7/8″ – Drawer Box Front Trim
- 1 – 3/4″ plywood at 13-3/4″ x 18″ – Door Base
- 3 – 1×3 at 13-3/4″ – Door Trim
Click on the drawings for a larger view!
Cut the pieces for the legs. Cut the taper using a jigsaw, bandsaw or a tapering jig on a table saw.
Cut the pieces for the side framing and the side panels. With the pocket hole jig set for 3/4″ material, drill pocket holes in each end of the framing pieces and all four edges of the panels. Secure the framing pieces to the legs using glue and 1-1/4″ pocket hole screws.
Secure the panels to the side framing assembly using glue and 1-1/4″ pocket hole screws. The back face of the panel will be flush with the back face of the side framing assembly.
Cut the pieces for the upper shelf and bottom, and drill pocket holes in the side edges. Secure the upper shelf and bottom to the sides using glue and 1-1/4″ pocket hole screws.
Cut the piece for the center shelf and drill pocket holes in the side edges. Position the shelf so it is flush with the back of the legs which will make it 1-1/2″ back from the front legs (to allow for the door). Secure the shelf to the sides using glue and 1-1/4″ pocket hole screws.
Cut the piece for the back. Secure the back using glue and 1-1/4″ brad nails.
Cut the piece for the top. The top will be flush with the back, and will overhang the sides and front by 1/2″. Secure in place using glue and 1-3/4″ brad nails.
Cut the pieces for the drawer boxes. Drill pocket holes in all four edges of the bottom as well as each end of the sides. Assemble the drawer boxes as shown using glue and 1-1/4” pocket hole screws.
Attach the 1×3 trim piece using glue and 1-1/4″ brad nails. Apply a coat of paste wax to the bottom of the drawer to help it slide smoothly.
Cut the pieces for the door. Attach the trim pieces as shown using glue and 1-1/4″ brad nails.
Install the hinges on the door, then install the door in the cabinet.
Finish as desired.
This cabinet would make a fabulous nightstand or an end table in a living room! Have any questions about the DIY plans to build a Cate Chest? Leave a comment below!
Originally posted 2015-11-19 08:00:27.
[…] Build a Cate Chest […]