Build a Monroe Dining Table
Easy to Build Large Family Dining Table, Inspired by World Market
This table is huge! Measuring at nearly 4 feet wide and 8 feet long, this table is perfect for a large family get-together or for any sort of soiree when entertaining a large number of guests! The plans to build a Monroe Dining Table uses straight off-the-shelf lumber, and is the perfect plan for any skill level! It has three leg columns underneath, tied together with stretchers and features a planked top with breadboard ends.
The plan requires no special tools or fasteners, and I’ve included a template for the curved braces which can easily be cut with a jigsaw or a bandsaw. It can be built for around $100, which is far less expensive than the inspiration piece which retails at $999!! This plan will be available soon in a shorter size!
- 2-1/2″ pocket hole screws (<– affiliate link)
- 2-1/2″ screws
- 1/4″ x 4″ lag screws with T-30 torx bit for a drill (<– affiliate link)
- Sandpaper (80, 120, 220 grits)
- Finishing Supplies
- 18 – 2×4 at 8′
- 1 – 2×6 at 4′
- 1 – 2×6 at 8′
- 2 – 2×10 at 8′
- 1 – 4×4 at 8′
- 3 – 4×4 at 25-1/2″ – Leg Base
- 3 – 2×4 at 36″ – Leg Base
- 3 – 2×4 at 31-1/2″ – Leg Base
- 12 – 2×10 at 9-1/4″ – Leg Base Braces
- 2 – 2×4 at 36″ – Leg Stretchers
- 3 – 2×6 at 42″ – Ends and Center of Top
- 24 – 2×4 at 38-1/2″ – Top
- 4 – 2×4 at 39″ – Top Supports
Notes About the Project:
- This table is a beast, so use caution when lifting the top (or the entire table, for that matter) and have a buddy around!
- It may be easier to thoroughly sand each piece prior to assembly.
- Finish the top and the base separately, then assemble.
- Contact me if you have any questions!
Cut the pieces for the leg bases. In the 36″ 2x4s, cut a 45° bevel in each end and sand so that the hard edges are slightly rounded over. Secure the 2x4s for the bases to the 4x4s using glue and the 1/4″ x 4″ lag screws. The screws for the top may have to be countersunk to allow for the top. (Use a Forstner bit at the same diameter as the head of the lag screws to pre-drill a shallow hole.)
Cut the pieces for the braces. There are four pages to the template – the pages are taped together with the registration marks aligned, then cut out and traced onto the wood.
The templates can be found here: Page 1, Page 2, Page 3, Page 4.
Cut out the braces using a jigsaw or a bandsaw. Position the leg braces so they are centered on the 2x4s and 4×4 that make up the leg base, securing in place with 2-1/2″ screws. The screws can be driven from the underside of the 2x4s, and toe-nailed through the braces into the 4×4.
Cut the pieces for the leg stretchers. Instead of drilling pocket holes on one wider flat surface of the stretchers, drill one pocket hole on each edge at each end which will allow the stretchers to be secured from the top and bottom with the pocket holes being hidden. DO NOT USE GLUE so that the stretchers can be removed from the leg bases if the table needs to be disassembled.
Cut the pieces for the top and drill pocket holes in each end of the 2×4 pieces. Assemble the top as shown, using glue and 2-1/2″ pocket hole screws.
Cut the pieces for the top supports, and cut a 45°bevel in each end of each piece. Secure the supports to the underside of the top, as shown, using glue and 2-1/2″ screws.
Position the leg assemblies upside down on the underside of the top. Secure in place using 2-1/2″ screws through the 2x4s in the base into the underside of the top. DO NOT GLUE THE TOP TO THE BASE in case the table needs to be disassembled.
This plan is the perfect choice for any skill level, and can be completed in a weekend! If properly finished (or constructed using exterior-rated wood), this would be a fabulous table for outdoor entertaining! Have questions about the plans to build a Monroe Dining Table? Leave a comment below!
Originally posted 2019-10-19 08:00:35.