Easy to Build Hair Accessories Storage

Inspired by Pottery Barn Teen

This hair accessories storage piece from PB Teen is so cute! $99.00 seems kind of steep so I figured I could hack it and make one myself! It cost me nothing… the plywood I used was sheathed around two sheets of walnut plywood I special ordered so it was free! (I’m sure I paid for it somewhere!)

hair accessories storage

 

Today, I’ll show how I built this and include the plans I drew up in case you’d like to build one for yourself or as a gift! We all know that Christmas is right around the corner and this would make a great gift!

I used plywood for the body and glue with 1-1/4″ brad nails to hold it all together! I omitted the drawer as I thought it might be a little too frustrating complicated to build correctly!

hair accessories storage dimensions

 

Materials:

  • 1/2″ plywood (Quarter sheet)
  • Glue
  • Brad nailer & 1″ brad nails
  • Jigsaw, Table saw, and/or Miter Saw
  • Square & a pencil
  • Tape Measure
  • Drill & 1″ paddle bit
  • Hole saws – 3.5″, 2.5″, 2″ (<– affiliate link!)

Begin by cutting the pieces as follows:

  • 2 @ 7″ x 9″ – Sides
  • 1 @ 4″ x 11″ – Top
  • 1 @ 6″ x 12″ – Front
  • 1 @ 7-1/2″ x 11″ – Large Divider
  • 1 @ 2-1/2″ x 4-1/2″ – Small Divider
  • 1 @ 7″ x 11″ – Bottom
  • 1 @ 9″ x 12″

It is a whole lot easier to sand each piece before assembly. I start with 80 grit, then 120 grit, and finish with 220 grit.

hair accessories storage plywood

 

Step One

Cut the pieces for the bottom and both dividers. I drew a line on the bottom piece 4″ from the back for placement of the larger divider. Attach the divider to the bottom with glue and 1″ brad nails.

hair accessories storage bottom dividers

 

hair accessories storage secured

Step Two

Mark the placement of the smaller divider and draw lines on the bottom as well as on the larger divider to center the pieces. (See the drawing above for placement measurements). Secure with glue and 1″ brad nails.

hair accessories storage smaller divider placement

 

hair accessories storage smaller divider

Step Three

Cut the pieces for the sides. Cut a 3″ long x 2-1/2″ wide notch in each side (see drawing).

hair accessories storage sides

 

Step Four

To cut the arch in the bottom, I clamped the sides together and drew lines where the cuts would be made. I used a paddle bit to drill a circle where I wanted the curved part of the arch to go.

hair accessories storage bottom arch

hair accessories storage paddle bit

 

Step Five

Using the paddle bit, I started to drill the holes at the mark I made until the pointed part of the bit went through both pieces. I then flipped the pieces over and continued drilling the hole from the other side. I get a lot less tearout by cutting holes this way…

hair accessories storage holes for arch

hair accessories storage back side

hair accessories storage holes cut through

Step Six

I used the jigsaw to cut the lines where they intersected with the holes.

hair accessories storage jigsaw cut

 

Step Eight

I then sanded any rough edges and attached the sides to the dividers as shown in the drawing.

hair accessories storage attach sides

hair accessories storage attach sides drawing

Step Nine

I repeated the arch-cutting process for the front and the back, then sanded any rough edges. I attached the front and back using glue and 1″ brad nails.

hair accessories storage top view

hair accessories storage back

hair accessories storage front

Step Ten

Before I worked on the final piece, I painted the inside. It didn’t have to be perfect but since the inside would be visible through the holes, I thought it might be a good idea to paint at least one coat on it!

I marked the placement for the holes in the top by drawing a horizontal line across the board and lining up the hole saws until I was happy with the spacing.

hair accessories storage hole placement

hair accessories storage hole dimensions

 

Step Eleven

I used three different sized hole saws (3-1/2″, 2-1/2″, 2-1/8″) and a scrap board underneath. I started drilling from one side, then flipped the board over to finish the hole – this helps reduce tearout.

hair accessories storage hole saw cut

hair accessories storage hole saw back

hair accessories storage completed holes

 

Step Twelve

I inserted the top piece, and held it in place so it was flush with the top of the sides, dividers, and back. I secured it to the box with 1″ brad nails. I filled in the nail holes and edges with Dry Dex, and sanded the entire piece with 220 grit sandpaper.

hair accessories storage secure top piece

 

Step Thirteen

I painted the entire piece with Behr Ultra Premium Plus in  Ultra Pure White Satin. Once it was dry, I sealed it with Rust-Oleum Ultimate Polyurethane in Matte Soft Touch. I had a hard time finding the perfect letter “H” for the front… I finally settled on a metal letter and glued it to the front with a couple dabs of Liquid Nails.

hair accessories storage monogram

 

 

This is an easy project perfect for those new to project or furniture building, and can be completed in a weekend! Have questions about the hair accessories storage? Leave a comment below!

Originally posted 2012-07-09 08:00:03.

8 Comments

  • Jasmine says:

    what are the measurements to cut the L- shape???

  • Chris says:

    I think you messed up on listing the sizes of the parts to cut. You have the sides at 7 3/4″ x 9″, but when you show the picture of the side it is 7″ x 9″. Looking at how it goes together I’m guessing it should be 7″ x 9″ (especially since I cut the 7 3/4″ x 9″ from your cut list and it looks like it will be too big).

  • inamays says:

    Curious to know why you didn’t use a 1″ hole saw to shape the bottoms, rather than a paddle bit. I find that paddle bits will tear the wood more easily than a good hole saw. Thanks for the plans here, I’m going to build this for my daughters birthday!

    • CherTexter says:

      Hello, there! I don’t usually have any problems with tearout using either bit – I always make sure I only drill about halfway through the piece, then flip the piece over and continue drilling out the hole. This reduces tearout and creates a clean hole whether I use a paddle bit or a holesaw.

      Good luck with your build and I’m sure your daughter will love it!

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.