DIY Plans to Build a Delilah Twin Bed
This simple bed is very easy to construct and is perfect for those new to woodworking or those who just want to take on an easy project. The DIY plans to build a Delilah bed use off the shelf boards and have narrow pieces on the headboard and footboard. Though there are a lot of pocket holes to drill, they are easily filled using a product such a Dry-Dex (if the bed will be painted) or a wood filler.
- 1-1/4″ pocket hole screws
- 2″ pocket hole screws
- 1-3/4″ brad nails
- 1-1/4″ screws
- Wood glue
- Sandpaper (100, 150, 220 grits)
- Finishing supplies (primer & paint, or stain, sealer)
- 2 – 1×2 at 8′
- 9 – 1×3 at 8′
- 3 – 1×6 at 8′
- 1 – 1×12 at 4′
- 2 – 2×4 at 8′
- 2 – 2×4 (ripped to 2-3/4″ wide) at 52-1/2″ – Headboard Legs
- 2 – 1×3 at 38″ – Headboard & Footboard Framing
- 2 – 1×6 at 38″ – Headboard & Footboard Framing
- 2 – 1×3 at 45″ – Headboard & Footboard Top Trim
- 8 – 1″ strips (ripped from 1×12) at 34-1/2″ – Headboard Framing Spindles
- 2 – 2×4 (ripped to 2-3/4″ wide) at 28-1/2″ – Footboard Legs
- 8 – 1″ strips (ripped from 1×12) at 10-1/2″ – Footboard Framing Spindles
- 2 – 1×6 at 78″ – Side Rails
- 2 – 1×2 at 78″ – Side Rail Slat Support
- 13 – 1×3 at 40″ – Slats
Click on the drawings for a larger view!
Cut the pieces for the headboard legs. The 2×4 pieces will be ripped to 2-3/4″ wide.
Cut the pieces for the headboard framing. For the framing spindles, cut the 1×12 into 1″ strips then cut them to length.
Set the pocket hole jig for 3/4″ material and drill pocket holes in each end of the framing pieces. Drill two pocket holes in each end of the 1×3 and 1×6 pieces, and one pocket hole in each end of the framing spindles. Assemble the headboard as shown using glue and 1-1/4″ pocket hole screws. The back face of the framing pieces will be flush with the back faces of the legs.
Cut the piece for the top trim. The back edge of the top trim will be flush with the back face of the framing and legs, and will overhang the sides by 3/4″. Secure the trim in place with glue and 1-3/4″ brad nails.
The footboard is constructed in exactly the same manner as the headboard – the legs and framing spindles are shorter!
Fill the pocket holes in the headboard and footboard with filler. Let the filler dry and then thoroughly sand.
Cut the pieces for the side rails and the side rail slat supports. Drill pocket holes in each end of the side rails. Secure the slat support to the side rail as indicated in the drawing using glue and 1-1/4″ screws.
Secure the side rails to the headboard and footboard using 2″ pocket hole screws. DO NOT use glue – this way the bed can be disassembled if necessary. The outside face of the side rail is located 3/4″ back from the side edge of the legs.
Cut the pieces for the slats. The slats are spaced approximately 3-1/2″ apart. Secure the slats to the slat supports using 1-1/4″ screws. DO NOT use glue.
Finish as desired.
This bed would be perfect for a kid’s room or a guest room, and would make a perfect gift like the one I made for my daughter! Have any questions about the DIY plans to build a Delilah Twin Bed? Leave a comment below!